Sunray Shadow

One of the simplest and most efficient salmon flies ever deceived. A wing on a tube, and that's it. And it's patented!

By Martin Joergensen

With the salmon season coming up in many parts of the world, I thought that a genuine salmon fly would be an appropriate thing to publish. And since there is a chance that I will be fishing for salmon this summer, I could whip out a few flies for that use at the same time.

Simplicity
I have always liked the Sunray Shadow. It's an extremely simple fly based on a very simple concept. It does what it's supposed to with a minimum of extras. The fly is basically a long, black wing on a tube, but with a stiff underwing to keep it from hooking itself and a visible top to add a little flash.

Ray Brooks' original was invented in Norway on the banks of the classic salmon river Laerdal. It became so popular and widespread and proved so efficient that the story tells that Brooks had it patented. I haven't been able to verify this, and I must say that the whole notion of patenting a fly pattern – and in particular one this generic – makes little sense to me. But that's another story.
No matter what this fly was highly successful and has now spread all over the world and is tied in a wealth of variations.

The original
Originally Brooks tied the fly with three materials: white-tipped squirrel, monkey hair and peacock herl. The stiff squirrel would lift the long wing free of the hook, the monkey would create the very long and mobile wing and the herl would accent the fly. A US friend of mine often says: any fly with peacock herl catches fish, and this pattern has proved him right again.

The Sunray Shadow is essentially a souped up Collie Dog - perhaps the ultimately minimalistic salmon fly. It is just a bunch of black hair from a Border Collie's tail on a tube, devised in the UK sometime in the eighteenth century.
Brooks added one functional material to this (the stiff underwing) and some flash (the herl) and got from that the Sunray Shadow.

Speaking of dogs
One of the reasons that I found the Sunray Shadow a suitable pattern for my own tying, was my dog, Divus. He might not be a Border Collie, but being a Shetland Sheepdog, he is pretty close. And while a Border Collie has suitable hair in the tail only, Divus has a whole body covered with Collie Dog and Sunray Shadow wings. Many a fly tyer has run his fingers through my dog's fur and gathered it into small bunches the size of a fly wing. But every time Divus has walked away with all his hair in place.
I, on the other hand, have the privilege of being allowed to actually take my scissors and cut a bunch! Not that I have asked the family for permission, but no one can see any difference as long as I don't start a wholesale production of flies.

Monkey, goat, dog
Brooks' original was utilizing hair from the black and white Colobus monkey, which is a fairly common and widespread African monkey with long, black and white, shiny hair. But monkey hair is both hard to find and politically very incorrect to use. And there is a large risk that is has been obtained illegally. Most monkeys are protected, and getting a hold of their skins means finding the monkeys in captivity. The black-and-white Colobus monkey is a threatened species listed under Appendix II in CITES, and requires special permits to be traded.

For us fly tyers all this means: look for replacements. If you don't have a black and white Sheltie and hand, goat seems to be the best bet for a monkey hair substitute. I do have a piece of black goatskin with hair, which is very similar to both the monkey and the dog, and I have tied flies with that too. It works just as well.

	Step 1 - tube and thread  Martin Joergensen
	Step 2 - underwing  Martin Joergensen
	Step 3 - main wing  Martin Joergensen
	Step 4 - herl  Martin Joergensen

Tying it
The Sunray Shadow is not exactly a big tying challenge, and if you want an entry point to tube flies, it gets no easier than this.
Tie the fly on a 1½ inch plastic tube. Mount a tube fly holder in your vice. You can use a tool made for the purpose or use a large needle or a large blind salmon hook to hold the tube.
Press the tube over the needle until it sits tight, and start the thread right behind the front collar of the tube and cover a small bit of the tube, no larger than the size of the head on the final fly. Some tubes come with no collar, and on these you can melt a small collar by holding the tube into a flame. Leave the rear end of the tube as it is.
Tie in a small bunch of squirrel or bucktail slightly longer than the tube. Top that with the goat hair, which should be about 4 inches long. Finish the fly with a couple of peacock herl over the wing.
Create a head that covers all the butts, whip finish, cut the thread and varnish a couple of times.

With coneheads  Martin Joergensen

Weight
The plastic tube Sunray Shadow is quite light and in order to get it down in fast water you will need a sinking line or leader. Alternatively you can tie the fly on a heavier tube or you can add weight to the fly in the form of a conehead.
Cut a ½ inch piece of thin inner tube. You need tube that fits snugly inside the cone as well as the main tube. Melt a collar in one end and slide the conhead facing forwards onto the tube. Add some instant glue to the outside of the tube, let it seep in under the conehead and slide the thin tube into the main tube, making sure that the conehead sits tightly against the front end of the fly and partially or fully covers the head of the fly. The latter depends on the size of the conehead and the size of the head on the fly. The glue binds in seconds and the conehead should be secured.

Another option is of course to tie the fly on a heavier tube like a bottle tube or a straight aluminum or copper tube. This will add a lot of weight to the fly itself. But many seasoned salmon anglers will prefer a lighter fly fished on a sinking line over a heavy fly on a floating line.

Fishing the fly
The most usual way of fishing this fly – and any salmon fly for that matter – is by casting it downstream and across, mending the line to let the fly sink and then just letting it swing across the current towards your own bank. The fly will work with the microcurrents in the water and thanks to the long and soft tail be very much alive. Some salmon anglers like to gently move the rod tip, inducing even more movement into the fly.
You can also mend the line upstream as the fly moves to decrease its speed and even make it sink a bit or mend downstream to speed it up, which will often elevate it a bit in the water column. No matter what you do the speed of the fly across the current will typically increase towards the end of the swing, and many salmon anglers experience that the fish will strike as the speed peaks and the drag in the rod is at its largest.

	A beautiful salmon pool  Nils Jorgensen	A small selection  Martin Joergensen

A less traditional way of fishing the Sunray is by casting it upstream and letting it sink. Since there is no drag from the line, the fly will sink faster this way, and you will be able to fish a lot deeper than on the downstream swing. Remember to keep contact with the fly when fishing upstream, enabling you to set the hook if a fish should strike the fly on the almost slack line.

Materials

Thread	Black
Tube	Plastic 1-1½ inch
Underwing	White bucktail
Main wing	Long black goat hair (or dog or monkey)
Overwing	Peacock herl